RED Systems supplies pumps, CSA-approved electric motors, VFDs, gearboxes, mechanical seals, and power transmission components for industrial, municipal, process, and commercial applications across Ontario. Select a category or request pricing.
Frame-mounted and close-coupled end suction centrifugal pumps for water, process, and general industrial service. Available in cast iron, stainless, and bronze construction.
ANSI B73.1 standard centrifugal pumps for chemical and process applications. Interchangeable dimensions across manufacturers simplify maintenance and spare parts management.
Self-priming centrifugal pumps for suction lift applications, solids handling, dewatering, and intermittent service where loss of prime is a concern.
Horizontal split case double-suction centrifugal pumps for high-flow, lower-head applications including water supply, fire protection, and HVAC.
Vertical turbine, vertical inline, and column pumps for sump, wet well, tank, and pit installations with limited floor space.
Submersible centrifugal and sewage pumps for wet well, lift station, drainage, and dewatering applications.
PC pumps for viscous fluids, sludge, slurry, and shear-sensitive product transfer in process and wastewater applications.
Hose and tube peristaltic pumps for chemical dosing. Rotary lobe pumps for sanitary and food process applications with CIP requirements.
Diaphragm and plunger metering pumps for precise chemical injection, water treatment dosing, and process chemical addition.
Pre-engineered pressure booster packages with pump, motor, tank, controls, and piping — ready to install for building, HVAC, and process pressure service.
Polypropylene, PVDF, aluminum, and stainless-steel AODD pumps for aggressive chemical transfer, drum unloading, and tank-to-tank transfer where containment and chemical compatibility are critical.
Cast iron and stainless AODD pumps with heavy-duty diaphragm and check valve materials for abrasive slurries, sludge, and high-solids fluids.
AODD pumps with large-bore porting and low-shear flow paths for viscous products including adhesives, pastes, thick coatings, and food-grade viscous fluids.
Compact and lightweight AODD pumps for portable transfer, drum emptying, and applications where no electrical power is available.
Totally enclosed fan-cooled (TEFC) motors for general industrial and pump drive applications. NEMA frame sizes from fractional to 500+ HP. Single-phase and three-phase. CSA approved.
C-face and D-flange JM and JP pump motors for close-coupled and frame-mounted centrifugal pump drives. Matched to pump end mounting dimensions.
Vertical hollow shaft solid-shaft motors for vertical turbine pump drives, column pumps, and deep well pump applications.
Severe-duty TEFC motors and IEEE 841 premium-efficient motors for demanding industrial environments including petrochemical and pulp & paper. Confirm IEEE 841 compliance per specific model.
UL/CSA-listed explosion-proof motors for Class I, Division 1 hazardous locations where flammable gases or vapours are present under normal operating conditions. Confirm class, group, and temperature code.
Motors suitable for Class I, Division 2 hazardous locations where flammable concentrations are not normally present but may occur under abnormal conditions. Confirm classification and grouping for the specific installation.
Inverter-duty motors designed for variable frequency drive applications with reinforced insulation, shaft grounding provisions, and suitable voltage spike tolerance.
Totally enclosed washdown motors in epoxy-coated or stainless-steel construction for food processing, beverage, pharmaceutical, and corrosive-environment applications.
IEC frame motors for metric mounting applications, OEM equipment, and replacement of international motor brands in process and manufacturing installations.
AC brake motors with integrated disc or drum brakes for applications requiring immediate stop, load holding, or vertical lifting drives.
VFDs for pump speed control, constant pressure operation, energy savings, and protection against dry run, overload, and single phasing. Compatible with inverter-duty and standard TEFC motors.
Electronic soft starters for reduced-voltage starting of centrifugal pumps and motors where full-voltage starting current is undesirable or supply limitations exist.
Pre-wired pump control panels with VFD or across-the-line starters, HOA switches, overload protection, and instrumentation for single and multi-pump installations.
Duplex and triplex alternating pump control panels for lead-lag pump operation, level or pressure-based switching, and equal run-time distribution across multiple pumps.
Pressure transducers, level switches, float controls, and transmitters for automatic pump start/stop and pressure set-point control.
VFD panels with manual bypass capability for critical pump applications where continuous operation is required even during VFD maintenance or failure.
Inline helical and parallel-shaft helical gearboxes for high-efficiency, moderate-to-high speed reduction in industrial drive applications.
Worm gear reducers for low-speed, high-torque applications including agitators, mixers, conveyors, and slow-speed drives requiring compact right-angle output.
Bevel helical and right-angle gearboxes where a directional change in drive shaft orientation is required alongside speed reduction.
Shaft-mounted gearboxes for direct mounting on the driven shaft — eliminating separate couplings and simplifying installation on conveyors and agitators.
Integrated motor and gearbox assemblies with matched torque, speed, and mounting for compact direct-drive applications. Reduce design and sourcing time.
Existing gearbox replacement by ratio, torque, service factor, mounting, shaft size, and centre distance. Provide nameplate data or drawing for cross-reference.
Spider-element jaw couplings for pump-to-motor connection with vibration dampening and misalignment tolerance. Standard bore or pilot bore with keyway.
Grid-spring and disc-pack couplings for higher torque, high-speed pump and compressor drives requiring precise torque transmission with low backlash.
Flexible elastomeric couplings for general-purpose pump and motor connections where angular, offset, and axial misalignment must be accommodated.
Classical, narrow, and cogged V-belts with matching sheaves for belt-driven pump, fan, and equipment applications. Proper belt selection critical to drive life.
Timing belts and synchronous pulleys for no-slip power transmission in applications requiring precise speed ratios.
QD and taper-lock bushings for sheave and sprocket mounting. Roller chain sprockets and chain for chain-drive applications.
OSHA-compliant coupling and belt guards for pump and motor installations. Fabricated steel and aluminium guards for NEMA and IEC frame sizes.
Ball, roller, and tapered roller bearings for pump bearing frames, motors, and rotating equipment. Pillow block and flange-mount units available.
Single-spring and multi-spring mechanical seals for general-purpose pump service in clean, non-hazardous fluids. Supplied as pusher or bellows-type depending on application.
Dual cartridge mechanical seals in back-to-back and tandem arrangements for toxic, hazardous, volatile, or environmentally sensitive fluids requiring zero-leakage or secondary containment.
Pre-set single cartridge seals for fast, accurate installation without measurement. Preferred over component seals where installation speed and accuracy are priorities.
Axially split mechanical seals for in-place installation without removing the pump from service. Suitable for large-bore pumps and difficult-to-access installations.
Metal bellows mechanical seals for high-temperature, cryogenic, and applications where elastomer O-rings would be attacked by the process fluid.
Double mechanical seals designed for mixer and agitator shafts, including top-entry, bottom-entry, and side-entry configurations.
Mechanical seal cross-reference and identification from pump brand, model, and serial number. Supply of OEM equivalent seals for most major pump manufacturers.
Braided compression packing, gland followers, and lantern rings for stuffing box applications where mechanical seals are not specified or practical.
Seal support system selection depends on process fluid type (clean, dirty, abrasive, toxic, or volatile), operating pressure and temperature, seal arrangement (single or dual), API flush plan required, fluid compatibility with barrier fluid, and reliability requirements. Contact RED Systems with seal datasheet and process conditions for support system recommendations.
RED Systems Fabrication Division assembles custom seal support skids combining reservoir, heat exchanger, instrumentation, piping, valves, and controls on a fabricated steel baseplate with documentation package including GA drawing, instrument list, and BOM.
Fabrication Division →Provide the application details, equipment model, or part number. RED Systems will confirm availability, lead time, and pricing.